Home

›

Residential

›

Passive House

Residential fire suppression

Passive House Fire Suppression Systems

Water mist fire suppression for Passivhaus and low-energy homes. Designed around the airtight layer and services, with small pipework and minimal impact on the building's performance.

✓ Water mist & sprinklers
✓ Design to commissioning
✓ UK-wide installation
Passive House Fire Suppression Systems

Fire tested to BS EN 14972-17:2025, the new UK standard for home water mist

Our residential water mist system has passed full-scale fire tests to BS EN 14972-17 at the FPA, a UKAS-accredited test house, making us one of the first UK companies to do so. It’s the standard that replaced BS 8458, which gives Building Control and approved inspectors confidence in your fire strategy.

Open-plan fire safety without the fire doors

Keep your open-plan kitchen, loft conversion or living space. Discreet DOME water mist nozzles provide an approved alternative to protected escape routes and can reduce the need for fire doors, subject to Building Control.

80% less water than a domestic sprinkler system

Our DOME Gen 2 nozzle uses around 8 litres per minute, compared with 45 to 60 for a typical sprinkler head. That means less water damage, smaller pipework, and in most homes no water storage tank.

British-designed, made and installed, with Building Control support

We design, manufacture, install and maintain every home water mist system in-house. Our compliance team works directly with Building Control to help get your project signed off.

OverviewRisk factorsRegulationsMist or sprinklerDesignStandardsProjectMaintenance & costFAQsEnquire
Residential fire protection

Fire protection that respects the build

Passive houses are built to tight tolerances. Every pipe that crosses the airtight layer needs planning, and services zones are often small. A fire suppression system has to fit that discipline, not fight it.

SmartMist's water mist system uses small-bore pipework and discreet heads, and can often run from the mains. We plan routes and penetrations with your architect and Passivhaus designer from the start, so protection doesn't compromise performance.

  • New Passivhaus and low-energy homes
  • EnerPHit and deep retrofits
  • Open-plan layouts and timber frame
See all residential fire suppression →
Fire protection that respects the build
What shapes the design

What shapes fire protection in a passive house

Two homes with the same floor area can need very different systems. These are the factors we look at first.

Airtight layer

Pipes crossing the airtight layer need sealed, planned penetrations. Fewer, smaller pipes make that easier.

Services zones

Pipework usually runs in a services void inside the airtight layer, alongside MVHR ducts.

Open-plan layouts

Open-plan stairs and living spaces can need suppression to meet escape rules.

Timber construction

Many passive houses are timber frame, which affects how fire spreads and what Building Control asks for.

Water supply

A mains-fed system avoids a tank and keeps plant inside the thermal envelope small.

Where you build

Wales requires sprinklers in all new homes. Elsewhere, suppression is often an alternative to other measures.

Requirements

Does a passive house need a sprinkler system?

In Wales, all new homes need one. In England and Scotland, it depends on the design: suppression is often used to allow open-plan layouts or where Building Control asks for it.

Wales

All new homes

Sprinklers have been required in all new and converted houses and flats in Wales since January 2016.

England

Approved Document B

Not required in most new houses, but suppression can support open-plan layouts or longer escape routes above 4.5m.

Scotland

Building Standards

Required in new flats and social housing. For private houses, it's used where the design calls for it.

Choosing a system

Water mist or fire sprinklers?

We install both, so we recommend whichever meets your design standard with the least water and disruption.

Water mist

Less water, often no tank

Water mist uses small-bore pipework and very little water, so fewer, smaller penetrations through the airtight layer and often no tank. Discreet heads suit clean Passivhaus interiors.

Explore residential water mist →
Fire sprinklers

The established, widely specified route

Residential sprinklers to BS 9251 are an option where a larger water supply is available or specified. They need larger pipes and often a tank, which is harder to accommodate in a passive house.

Explore residential sprinklers →
Mist and sprinklers aren't interchangeable in every building. We confirm the design standard with Building Control and your fire engineer before design, then recommend the system that meets it.
Design & installation

Designed with the building, installed around residents

We join the project early, agree pipe routes and penetrations with your architect and Passivhaus designer, and coordinate with MVHR and other services.

First fix happens with the services, with the second fix and commissioning after decoration, and we provide everything Building Control needs.

Send your drawings

Airtightness

Planned, sealed penetrations through the airtight layer.

Services zones

Pipe routes coordinated with MVHR and electrics.

Mains-fed

No tank where the mains can supply the flow.

Discreet heads

Flush heads that suit clean interiors.

Standards & compliance

Standards for passive house fire suppression

Which standard applies depends on the system, the building and, often, Building Control.

Standard
Relevance
Status

Approved Document B

Building Regulations fire safety guidance for dwellings in England.

Current

BS EN 14972-17:2025

The European fire test standard for residential water mist. Our SmartMist DOME™ residential water mist system has met the performance criteria of the BS EN 14972-17 open room fire test (3.5 m room height) at the FPA, a UKAS-accredited fire test laboratory.

Tested

BS 8458:2015

The former UK residential water mist standard, withdrawn by BSI in July 2025 and replaced by BS EN 14972-17.

Withdrawn

BS EN 14972-1

The European standard for water mist design, installation, inspection and maintenance. Every SmartMist water mist installation is designed to it.

Designed to

BS 9251:2021

Code of practice for sprinkler systems in domestic and residential occupancies.

Current

This page explains typical requirements. It isn't a fire strategy or design specification.

Certification & accreditation

ISO 9001:2015
Quality management
SafeContractor
Health and safety accreditation

Tested to BS EN 14972-17:2025 at the FPA

Our SmartMist DOME™ residential water mist system met the performance criteria of the open room fire test (3.5 m room height) at the FPA's UKAS-accredited fire test laboratory. Every installation is designed to BS EN 14972-1.

See all our accreditations →

Recent Clients

Passive House, Fire Suppression, Cornwall, UK
Project example

Passive House, Fire Suppression, Cornwall, UK

Passive House, Cornwall

SmartMist undertook a distinctive project in Cornwall, focusing on a Passive House – a building standard characterized by energy efficiency, reduced ecological footprint, and exceptional thermal comfort. Our task was to install an advanced fire suppression system, tailored to meet the unique requirements of this energy-efficient home.

How we work

From drawings to handover

01

Review

Send drawings and the fire strategy. We'll confirm the likely system and design standard.

02

Design

Layouts, hydraulic calculations and documents for Building Control and your warranty provider.

03

Install

Planned around your build programme or residents.

04

Commission

Testing, handover pack and a maintenance plan from day one.

Aftercare

Servicing, including systems we didn't install

Residential systems need an annual service, plus the simple owner checks the design standard sets. We check pumps, valves and heads, and keep the records Building Control, landlords and insurers expect. We also maintain systems installed by other contractors.

Service & maintenance plans →
Cost

What affects the price

  • Floor area and rooms: sets head count
  • Mist or sprinkler: changes pipe size and whether a tank is needed
  • Stage of build: early coordination costs less than late changes
  • Airtightness detailing: penetration seals and services routes
  • Water supply: mains pressure and flow
  • Location: Wales requires full coverage

Most projects are quoted after a drawing review.

Read our cost guide →
Guides

Regulations and guidance

FAQs

Passive house fire suppression FAQs

Will a fire suppression system affect airtightness?

Not if it's planned. Water mist uses small-bore pipework, so there are fewer, smaller penetrations, and we agree each one with your Passivhaus designer so it can be sealed properly.

Does a passive house need a tank for its sprinkler system?

Often not. Water mist uses very little water and can usually run from the mains, so there's no tank to fit inside the thermal envelope.

Is fire suppression required in a passive house?

In Wales, all new homes need it. In England and Scotland, it depends on the design: suppression is often used to allow open-plan layouts, or where Building Control asks for it.

When should we involve you in the project?

As early as possible, ideally at design stage, so pipe routes and penetrations are planned with the airtightness and services strategy.

Is BS 8458 still current for water mist systems?

No. BSI withdrew BS 8458:2015 in July 2025 and replaced it with BS EN 14972-17, the European fire test standard for residential water mist.

Our SmartMist DOME™ residential water mist system has met the performance criteria of the BS EN 14972-17:2025 open room fire test (3.5 m room height) at the Fire Protection Association (FPA), a UKAS-accredited fire test laboratory, and every installation is designed to BS EN 14972-1. If you have an existing system, keep it serviced and speak to us before any alterations or extensions.

Are SmartMist residential water mist systems independently tested?

Yes. Our SmartMist DOME™ residential water mist system has met the performance criteria of the BS EN 14972-17:2025 open room fire test (3.5 m room height) at the Fire Protection Association (FPA), a UKAS-accredited fire test laboratory. Every installation is also designed to BS EN 14972-1, the European standard for water mist design, installation, inspection and maintenance.

BS EN 14972-17 replaced the previous UK residential water mist standard, BS 8458, which BSI withdrew in July 2025. See our full fire test and certification record.

Will all the nozzles activate in my property in the event of a fire?

No, that is a myth. Only the nozzle where the frangible bulb breaks will be activated, in the unfortunate event of a fire.

Does smoke caused by burning food trigger the water mist nozzle?

No. Smoke does not trigger the nozzle. The bulb inside each nozzle only breaks with direct heat from a fire, at 57°C (135°F).

A nozzle near an oven won't be set off by opening the oven door, because the heat disperses quickly into the room.

Are misting fire suppression systems safe for electronics and furniture?

Yes, misting systems use fine water droplets that reduce fire damage without excessive water exposure, making them safe for electronics and furniture.

Get a quote

Have a project in mind?

Send what you have. These help us quote faster:

  1. Floor plans and sections
  2. Construction type
  3. Stage of build
  4. Building Control requirements, if known
  5. Airtightness and services strategy
  6. Mains water pressure and flow
  7. Programme
  8. Architect or Passivhaus designer contact

Or call 0330 113 5900

Upload Floor Plan Drag and drop files here or click to choose
No file chosen
Should be Empty:
Related

Other residential sectors

No items found.
Get a quote

Call Us