
Residential Fire Suppression


Water mist fire suppression for industrial fryers and oil cookers in food production. Fast, automatic protection that cools burning oil, limits damage and gets your line back into production sooner.

Water mist or sprinklers: independent advice, design and installation
As a commercial fire suppression specialist, we design and install both water mist and sprinkler systems, so we can recommend what actually suits your building, budget and fire strategy.
LPCB-certified water mist nozzles and in-house compliance expertise
Our commercial water mist systems use LPCB-certified nozzles. Our in-house compliance team prepares statements of equivalence and works directly with fire engineers, approved inspectors and fire authorities.
Full BIM coordination in Revit and AutoCAD
We coordinate fire suppression design with M&E and other services using BIM, cutting clashes on site and helping consultants and main contractors keep projects on programme.
UK water mist manufacturer with nationwide installation
We’re a SafeContractor-approved, British manufacturer of water mist fire suppression systems, supplying, installing and maintaining commercial systems across the UK through our accredited network.
Industrial fryers hold large volumes of oil at high temperatures, often running around the clock. If the oil overheats or a control fails, it can reach its auto-ignition temperature, and an oil fire can spread through the hood, exhaust and production hall.
SmartMist provides water mist fire suppression for industrial fryers and oil cookers, designed to meet both your operational needs and your insurer's requirements. Water mist droplets are a fraction of the size of sprinkler droplets. In the heat of a fire they turn to steam, cooling the oil and displacing oxygen without the violent reaction water causes on burning oil.

Two sites with the same floor area can need very different systems. These are the factors we look at first.
Cooking oil held near its limits can auto-ignite if temperature controls fail. Protection must work on a deep, burning oil surface.
Fire travels into the fryer hood and exhaust ductwork. Systems protect the hood, exhaust and the oil bath together.
Lines often run 24/7. A fire stops production, and clean-up and repair time matter as much as the fire itself.
Oil cooker fires are hard to put out. Systems should be tested for industrial oil cookers, not just commercial kitchens.
Insurers commonly require automatic protection on oil cookers and may set the design standard.
Heating, conveyors and exhaust fans should shut down when the system activates.
Building Regulations don't name it, but your fire risk assessment and insurer usually do: automatic protection on oil cookers is a common insurance requirement.
The European fire test protocol for water mist systems protecting industrial oil cookers with open nozzles.
Insurers commonly expect automatic suppression on industrial oil cookers, with interlocks and documented maintenance.
The Regulatory Reform (Fire Safety) Order 2005 requires a fire risk assessment, which must address fryer and oil fire risks.
We install both, so we recommend whichever meets your design standard with the least water and plant space.
High-pressure water mist uses up to 90% less water than traditional sprinklers. Fine droplets turn to steam over the burning oil, cooling it and cutting off oxygen, so damage is limited and repair and cleaning costs are lower. Systems are flexible enough to suit any oil cooker installation.
Explore commercial water mist →Standard sprinklers aren't suitable over hot oil, as large droplets can make an oil fire worse. Sprinklers still protect the wider production hall, and we make sure the fryer system and building sprinklers work together.
Explore commercial sprinklers →We survey the fryer, its hood and exhaust, and how the line operates. The system is designed to the oil cooker's size and layout, with detection and shutdown coordinated with your controls.
Installation is planned around production, and we train your team and service the system after handover.
Nozzles over the oil surface and inside the hood.
Protection for the exhaust and ductwork.
Heat detection with automatic and manual release.
Heating, conveyor and fan interlocks.
Which standard applies depends on the system, the building and, often, your insurer.
Water mist fire test protocol for industrial oil cookers.
Water mist fire test protocol for commercial deep fat fryers.
Design, installation and maintenance framework for water mist systems.
Requires a suitable fire risk assessment for the site.
This page explains typical requirements. It isn't a fire strategy or design specification.
UK designed and built
Water mist and sprinkler systems
Send drawings and the fire strategy. We'll confirm the likely system and design standard.
Layouts, hydraulic calculations and documents for your insurer and Building Control.
Planned around your build programme or operating hours.
Testing, handover pack and a maintenance plan from day one.
Commercial systems need an annual service, plus the routine owner checks the design standard sets. We test pumps and valves, check heads and nozzles for damage and obstruction, and provide the service records insurers expect. We also maintain systems installed by other contractors.
Service & maintenance plans →Most projects are quoted after a drawing review.
Read our cost guide →Building Regulations don't name it, but your fire risk assessment and insurer usually require it. Automatic protection on industrial oil cookers is a common insurance requirement.
Large water droplets can make a burning oil fire worse. Water mist droplets are much smaller and turn to steam over the oil, cooling it and cutting off oxygen.
The oil bath, the hood and the exhaust, with interlocks that shut down heating, conveyors and fans when it activates.
Water mist uses very little water, so there's less damage and less to clean. That usually means lower repair costs and a quicker restart than with a sprinkler discharge.
Yes. We offer a full service including design, installation, commissioning, scheduled maintenance, compliance checks, and emergency support.
Yes. We can inspect, upgrade, and maintain existing mist or sprinkler systems to bring them in line with current regulations and performance expectations.
We plan every installation carefully to minimise disruption. Work can be phased or scheduled outside business hours to maintain normal operations where possible.
Our commercial water mist systems are designed to BS EN 14972-1, and our commercial sprinkler systems to BS EN 12845.
For residential projects, our sprinklers are designed to BS 9251. Our SmartMist DOME™ residential water mist system has met the performance criteria of the BS EN 14972-17:2025 open room fire test (3.5 m room height) at the FPA, a UKAS-accredited fire test laboratory, and every installation is designed to BS EN 14972-1. We also work to project and insurer requirements.
We assess your fire strategy, occupancy type, building design, and water supply. Based on this, we may recommend high-pressure mist, low-pressure mist, wet or dry sprinkler systems, or a hybrid approach.
We recommend annual servicing in line with BS 9251, BS EN 14972-1 or BS EN 12845, depending on the system type. In high-risk or heavily used environments, more frequent checks may be required.
Yes. SmartMist offers both advanced water mist systems and traditional commercial sprinkler systems. We recommend the most suitable option based on your building’s fire strategy, layout, risk profile, and water supply.
Send what you have. These help us quote faster:
Or call 0330 113 5900